ProtectorGlaze
ProtectorGlazeTM is the new and revolutionary peelable temporary glass protection product that may also be used for other non-porous materials / surfaces.
ProtectorGlazeTM is a water based, non-toxic, liquid applied peelable protective coating that quickly sets to form a clear, durable protective coating.
ProtectorGlazeTM is an easily applied and cost-effective solution to on-site glass damage. Once the surface is ready to use, simply peel off by hand (no tools or razor blades required) in one continuous sheet.
ProtectorGlazeTM can be applied to glass that has not been cleaned and will remove any existing site dust.
Conventional roll-based protective films tend to peel away from the glass, when subjected to moisture and UV. Non-hazardous, biodegradable and totally environmentally friendly, ProtectorGlazeTM provides the perfect alternative to roll-based protective film products.
Ask your window installer not only to provide protection to the frame, but also to use ProtectorGlazeTM for temporary glass protection.
PRODUCT INFORMATION
A Temporary Protective, Water Resistant Peelable Coating For Windows and Other Surfaces:
Colour: Clear When Dry
ProtectorGlazeTM is a Peelable coating formulated for use on windows that require temporary protection from other building trades. Apply ProtectorGlazeTM by roller.
The excellent shielding of ProtectorGlazeTM hides inside activities from outside view. The coating is transparent in colour that will allow natural diffused light into the building. When inside redecoration is finished, remove ProtectorGlazeTM by peeling, leaving the inside showroom window in sparkling clean condition.
ProtectorGlazeTM represents the ultimate in non-solvent, water borne, strippable coatings.
ProtectorGlazeTM contains no flammable solvents.
Advantages:
- Safe to use. Clear dry film.
- Water resistant when dry. Water cleanable when wet.
- Excellent hiding / shielding. Easy to use.
- Non-flammable.
- Creates one tenth of the volume of waste that conventional protective films create.
Application:
ProtectorGlazeTM is normally used as received. It can be applied by, roller, or brush. The coating dries, depending on humidity and film thickness, in 30 minutes to 4 hours. ProtectorGlazeTM should be applied to yield a dry film of two to six mils (.002" to .006") thick. The dry coating is resistant to attack by water and can be washed, if so desired. Application temperatures range from 15F. to 48o Celsius.. ProtectorGlazeTM dries upon water evaporation. Faster dry can be realized by simple placement of air fans to remove the water from the coating. Rollers can be cleaned with water immediately after film application.
Removal:
ProtectorGlazeTM is removed by peeling. Simply, pry a piece of coating in one corner and lift.
Flammability:
Water Resistant ProtectorGlazeTM presents no fire hazard as received, during, or after application.
Disposal:
ProtectorGlazeTM is formulated to exclude ingredients that are deleterious to the painting process, such as silicones, or to the water wash system, such as foam generating or foam stabilizing ingredients.
FIRST TIME APPLICATION:
Cleaning of equipment:
Wet coating is easy to remove. Dry coating is water resistant and washing equipment with solvents might be necessary. Prolong soak in water will help coating removal easier.
Immediately after application, brushes and rollers should undergo a thorough rinse with water. Make sure that all paint residues are removed.
APPLICATIONS
Windows
Apply ProtectorGlazeTM peelable protective coating to the windows prior to the commencement of the brickwork operation to prevent falling mortar adhering to the glass. A thicker second application on external window sills will give excellent protection. Apply internally prior to the internal trades operation commencing.
TECHNICAL INFORMATION
When using the ProtectorGlazeTM peelable glass protection product, several key conditions of use must be strictly adhered to.
- ProtectorGlazeTM is roller applied to main area of glass, brush applied second coating to perimeter of area only.
- Apply only with ProtectorGlazeTM rollers. The use of other rollers may apply the product too thinly causing the product to be difficult to peel off.
- Do not apply the product:
-
in very heavy rain;
when the temperature is below 3oC or above 24oC. - Do not remove the product: until fully cured - generally 24-36 hours minimum depending upon temperature and airflow. Product can remain in situ for up to 12 months; in temperature below 5oC and above 26oC;
- with any sharp implements. Simply peel off from one corner.
- If the product is to be applied to framework, aluminium or PVCu:
- once 'touch dry', apply a second coat;
- do not coat handles or locking mechanisms;
- do not coat where there is a likelihood a vent/door may be opened.
- Do not store the product where it may be liable to freeze.
- ProtectorglazeTM can be applied by our customers own operatives or by Protectall International Ltd, as part of our supply and application service.
- Protectall International Ltd. will, through its team of operatives, provide initial factory training to demonstrate correct application procedures.
- It is recommended that glazing gaskets be inserted prior to applying ProtectorGlazeTM
- Ideally, glazing should be protected as it is installed; e.g. towards the end of a working day.
- When trained, an applicator should, dependant on site conditions, be able to cover between 25-50m 2 per hour.
- Wash out rollers with clean water after use.
- Any unused volume of product left in the roller tray may be returned to the storage drum providing it has not begun to set.
- Ensure all opened drums are resealed when not in use and during transportation.
- ProtectorGlazeTM has a shelf life in excess of 12 months when unopened.
- One litre of ProtectorGlazeTM applied with the ProtectorGlazeTM roller, will cover 6-8m 2 of glazing.
IMPORTANT: do not use 'off the shelf' general decorating rollers; these may not apply the product at the correct thickness.
COSHH
Material Safety Data Sheet
APPENDIX C - MATERIAL SAFETY DATA SHEET
PRODUCT ProtectorGlazeTM
--------------------------------------------------------------------
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION
PRODUCT NAME: ProtectorGlaze� PEELABLE COATING
SUPPLIER: Protectall International Ltd.
--------------------------------------------------------------------
2. COMPOSITION/INFORMATION ON INGREDIENTS
--------------------------------------------------------------------
3. HAZARDS IDENTIFICATION
Not regarded as a health or environmental hazard under current legislation.
--------------------------------------------------------------------
4. FIRST AID MEASURES
SKIN CONTACT: Frequent or prolonged skin contact may irritate skin.
EYE CONTACT: Slightly irritating but does not injure eye tissue.
INHALATION: Vapours may be irritating to respiratory system and nasal passages.
INGESTION: Low toxicity. No hazard with normal use.
CHRONIC: None known.
--------------------------------------------------------------------
5. FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
This product is non flammable. Use fire-extinguishing media appropriate for surrounding materials.
--------------------------------------------------------------------
6. ACCIDENTAL RELEASE MEASURES
PERSONAL PRECAUTIONS
Wear protective clothing as described in Section 8 of this safety data sheet.
ENVIRONMENTAL PRECAUTIONS
Do not allow to enter drains, sewers or watercourses. Contain spillages with sand, earth or any suitable absorbent material. Transfer liquid to containers, if possible, for recovery or disposal.
SPILL CLEAN UP METHODS
Flush away spillage with plenty of water. Spill emulsion very slippery. Avoid falls.
--------------------------------------------------------------------
7. HANDLING AND STORAGE
USAGE PRECAUTIONS
Avoid spilling, skin and eye contact. Do not use in confined spaces without adequate ventilation and/or respirator.
STORAGE PRECAUTIONS
Keep containers tightly closed. Keep in original container. Keep away from food, drink and animal feeding stuffs. Store above freezing. Minimise contact with air to prevent bacterial growth.
STORAGE CLASS
Chemical storage.
--------------------------------------------------------------------
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
PROTECTIVE EQUIPMENT
Approved goggles.
Approved gloves.
--------------------------------------------------------------------------------ENGINEERING MEASURES
Provide adequate general and local ventilation.
RESPIRATORY EQUIPMENT
Respiratory equipment may be required.
HAND PROTECTION
Wear protective gloves.
EYE PROTECTION
Wear approved safety goggles.
OTHER PROTECTION
Wear appropriate clothing to prevent any possibility of liquid contact and repeated or prolonged vapour contact.
HYGIENE MEASURES
Wash at the end of every work shift and before eating, smoking and using the toilet. Wash promptly if skin becomes wet or contaminated. Promptly remove any clothing that becomes wet. When using do not eat, drink or smoke.
--------------------------------------------------------------------
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Viscous liquid
COLOUR: White
ODOUR: Mild odour
RELATIVE DENSITY: 1.07
VISCOSITY: FORD CUP 4 80-120 s 20deg C
FLASH POINT (DEG C): Non Flammable
EXTINGUISHING MEDIA: Non Flammable
FIRE FIGHTING PROCEDURES: This product is non flammable and does not cause hazard.
--------------------------------------------------------------------
10. STABILITY AND REACTIVITY
STABILITY
Stable under normal temperature conditions and recommended use.
--------------------------------------------------------------------
11. TOXICOLOGICAL INFORMATION
INHALATION: May cause irritation to the respiratory system.
INGESTION: May cause discomfort if swallowed.
SKIN CONTACT: Liquid may irritate skin.
EYE CONTACT: Splashes may irritate.
--------------------------------------------------------------------
12. ECOLOCICAL INFORMATION
EXOTOXICITY
The product components are not classified as environmentally hazardous. However, this does not Exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment.
--------------------------------------------------------------------
13. DISPOSAL CONSIDERATIONS
GENERAL INFORMATION
The dried ProtectorGlazeTM can be disposed of in a landfill and will decompose over a period of time, and does not contaminate the environment.
--------------------------------------------------------------------
14. TRANSPORT INFORMATION
GENERAL: The product is not covered by international regulation on the transport of dangerous goods (IMDG, IATA, ADR, RID)
PROPER SHIPPING NAME: Non required
ROAD TRANSPORT NOTES: Not classified
SEA TRANSPORT NOTES: Not classified
AIR TRANSPORT NOTES: Not classified
UN NO. ROAD: 0
--------------------------------------------------------------------
15. REGULATORY INFORMATION
RISK PHRASES
Not classified.
SAFETY PHRASES
Not classified.
UK REGULATORY REFERENCES
Chemicals (Hazard Information and Packaging) Regulations.
APPROVED CODE OF PRACTICE
Classification and Labelling of Substances and Preparations Dangerous for Supply. Safety Data Sheets for Substances and Preparations.
GUIDANCE NOTES
Occupational Exposure Limits EH40
--------------------------------------------------------------------
16. OTHER INFORMATION
REVISION DATE MARCH 2005
DISCLAIMER
Information presented herein has been compiled from information provided to us by our suppliers and other sources considered to be dependable, and is accurate and reliable to the best of our knowledge and belief but it is not guaranteed to be so.
Nothing herein is to be construed as recommending any practice or the use of any product in violation of any patent of in violation of any law or regulation. It is the user's responsibility to determine the suitability of any material for a specific purpose and to adopt such safety precautions as may be necessary.
We make no warranty as to the results to be obtained in using any material and, since conditions of use are not under our control, we must necessarily disclaim all liability with respect to the use of material supplied by us.
